Exam Deatils

  • Exam Code
    :200-301
  • Exam Name
    :Cisco Certified Network Associate
  • Certification
    :CCNA
  • Vendor
    :Cisco
  • Total Questions
    :148 Q&As
  • Last Updated
    :Mar 25, 2020

Cisco CCNA 200-301 Questions & Answers

  • Question 1:

    Which type of address is the public IP address of a NAT device?

    A. outside global

    B. outsdwde local

    C. inside global

    D. insride local

    E. outside public

    F. inside public

  • Question 2:

    Refer to the exhibit. Users in your office are complaining that they cannot connect to the severs at a remote site. When troubleshooting, you find that you can successfully reach the severs from router R2.

    What is the most likely reason that the other users are experiencing connection failure?

    A. interface ports are shut down on the remote servers

    B. The DHCP address pool has been exhausted

    C. The ip helper-address command is missing on the R2 interface that connects to the switch

    D. VLSM is misconfigured between the router interface and the DHCP pool.

  • Question 3:

    Refer to the exhibit. When PC 1 sends a packet to PC2, the packet has which source and destination IP address when it arrives at interface Gi0/0 on router R2?

    A. source 192.168.10.10 and destination 10.10.2.2

    B. source 192.168.20.10 and destination 192.168.20.1

    C. source 192.168.10.10 and destination 192.168.20.10

    D. source 10.10.1.1 and destination 10.10.2.2

  • Question 4:

    Refer to the exhibit. Which two statements about the interface that generated the output are true? (Choose two.)

    A. learned MAC addresses are deleted after five minutes of inactivity

    B. the interface is error-diabled if packets arrive from a new unknown source address

    C. it has dynamically learned two secure MAC addresses

    D. it has dynamically learned three secure MAC addresses

    E. the security violation counter increments if packets arrive from a new unknown source address

  • Question 5:

    Refer to the exhibit. Which two events occur on the interface,if packets from an unknown Source address arrive after the interface learns the maximum number of secure MAC address? (Choose two.)

    A. The security violation counter dose not increment

    B. The port LED turns off

    C. The interface is error-disabled

    D. A syslog message is generated

    E. The interface drops traffic from unknown MAC address

  • Question 6:

    Refer to the exhibit. Which two statements about the network environment of router R1 must be true? (Choose two.)

    A. there are 20 different network masks within the 10.0.0.0/8 network

    B. A static default route to 10.85.33.14 was defined

    C. Ten routes are equally load-balanced between Te0/1/0.100 and Te0/2/0.100

    D. The 10.0.0.0/8 network was learned via external EIGRP

    E. The EIGRP administrative distance was manually changed from 90 to 170

  • Question 7:

    Refer to the exhibit. Which statement about the interface that generated the output is true?

    A. Five secure MAC addresses are dynamically learned on the interface.

    B. A syslog message is generated when a violation occurs.

    C. One secure MAC address is manually configured on the interface.

    D. One secure MAC address is dynamically configured on the interface.

  • Question 8:

    Refer to the exhibit.

    Which two statements about the interface that generated the output are true? (Choose two.)

    A. Two secure MAC address are manually configured on the interface.

    B. A syslog message is generated when the maximum number of secure MAC addresses is on the interface.

    C. The interface is error -disabled.

    D. The interface dynamic ally learned two secure MAC addresses.

    E. An SNMP trap is generated when the maximum number of secure MAC addresses is reached on the interface.

  • Question 9:

    Refer to the exhibit. Which two statements are true about the loopback address that is configured on RouterB? (Choose two.)

    A. It ensures that data will be forwarded by RouterB.

    B. It provides stability for the OSPF process on RouterB.

    C. It specifies that the router ID for RouterB should be 10.0.0.1.

    D. It decreases the metric for routes that are advertised from RouterB.

    E. It indicates that RouterB should be elected the DR for the LAN.

  • Question 10:

    Refer to the exhibit. Which switch in this configuration becomes the root bridge?

    A. SW1

    B. SW2

    C. SW3

    D. SW4

Tips on How to Prepare for the Exams

Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Gk4exam.com, you will find all the answers. Gk4exam.com provide not only Cisco exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your 200-301 exam preparations and Cisco certification application, do not hesitate to visit our Gk4exam.com to find your solutions here.